Steve Leibson

SPMT engulfs LPDDR2 standard, making adoption a no-brainer. Meanwhile Marvell jumps on the bandwagon.

June 7, 2010 on 9:00 am | In DRAM, Design, LPDDR2, Low-Power, SDRAM, SOC | No Comments

An insidious power problem has slowly crept up on embedded-system designers. While most of us were firmly focused on the power dissipation of our ever-expanding logic designs with their increasing number of processor cores in multicore designs, we mostly ignored the huge leaps in power consumption being caused by the rapid growth in memory size and big jumps in memory-access speeds and memory bandwidth. To cut memory costs, most high-end mobile and embedded designs today employ one high-bandwidth SDRAM device or array to satisfy all of a system’s memory requirements. Yet we think very little about the power impact of hooking big DDR SDRAMs up to our SOCs and ASICs—and these SDRAMs run at clock rates measured in hundreds of MHz or GHz, at transfer rates that are double the clock rate. It takes some real power to sling bits between a processor and SDRAM at transfer rates approaching or exceeding 1 Gtransfers/sec and even though the supply and I/O voltages have been dropping on SDRAM keeping memory power somewhat in check (only somewhat), wide DDR2 and DDR3 memory interfaces that deliver the highest bandwidths may now consume Watts of power. Watts! This simply cannot stand.

Not coincidentally, that’s the position of the SPMT (Serial Port Memory Technology) Consortium, which has been developing a low-power, high-performance memory interface for mobile and embedded applications. The low-power aspect arises primarily from SPMT’s use of low-voltage differential signaling (LVDS), which transfers information using 150 mV differential signal swings instead of single-ended, ground-referenced signal swings of more than a volt. The high-performance aspect arises from the use of multi-Gbits/sec transfer rates per SPMT data lane.

But there’s been a big, ugly fly in the SPMT ointment. Memory vendors know that more than 80% of all DRAMs go into PCs and servers and they stick with memory designs—and memory interfaces in particular—that best suit the needs of PC and server designers. Today, that means DDR2 memory, which is the mainstream DRAM technology, but the industry is quickly switching to DDR3. DDR4 is yet undefined but it too is a rapidly approaching memory-interface specification that will most assuredly ”fix” the problems we have with DDR3. These PC- and server-centric, high-speed parallel SDRAM interfaces burn a lot of power to deliver high bandwidth, which creates the niche opportunity that the SPMT Consortium has been trying to fill for mobile and embedded designs. Unfortunately, DDR memory has such a huge presence in the DRAM arena that there’s been little chance for any other interface approach to take hold.

Until now.

Today, the SPMT Consortium announced a major revision to the SPMT standard that may well spell the difference between an interesting technical exercise and an immensely successful new memory-interface standard. Previously, the SPMT specification multiplexed read/write commands and the data on the same unidirectional LVDS lanes. Doing so somewhat reduced the throughput on the data lines but it also reduced the memory pin count because SPMT memory didn’t need separate control/address (CA) lines. The reduced pin count was considered a major benefit that reduced the cost of packaged SPMT memory devices. The new SPMT specification, which completely supersedes the prior specification, does away with this control/address/data multiplexing in favor of using the same CA signal and pin definitions that LPDDR2 memory uses to carry control and address signaling.

This is a significant and important change to the SPMT spec because LPDDR2 is already poised to take over the mobile and embedded design spaces. (See LPDDR2: The new mainstream memory for embedded and mobile applications? on Denali Software’s Memory Report blog.) Further, four pairs of unidirectional SPMT data lanes now precisely overlap the 16 bidirectional data lines of a x16 LPDDR2 memory, making it possible to build one memory chip that can support both LPDDR2 and SPMT protocols using the same set of pins. What that means is that with only a few changes to the memory controller and memory PHY, an SOC or embedded processor can accommodate both LPDDR2 and SPMT memory using exactly the same set of interface pins. It also means that SDRAMs designed to the new SPMT specification can be used as LPDDR2 SDRAMs, ensuring a ready market when commercial SPMT SDRAMs first hit the market near the end of 2011—assuming things go according to the SPMT Consortium’s current plans.

So where’s the power advantage? It kicks in after the required SDRAM transfer rate hits a critical level. For example, the SPMT Consortium’s data estimates that a x32 LPDDR2 memory interface operating at 400MHz dissipates about 180mW while providing 3.2 Gbytes/sec of peak data throughput over 32 data lines (800 Gbits/sec/pin) and 360mW at a peak data throughput of 6.4 Gbytes/sec over 64 data lines. (Regular old DDR2 and DDR3 SDRAM interfaces would consume a lot more power than this.) By contrast, the SPMT interface dissipates 180mW while transferring 6.4 Gbytes/sec over eight data lanes (8 Gbits/sec/lane) and 360mW when transferring 12.8 Gbytes/sec over 16 data lanes. So the SPMT interface appears to be about twice as power efficient as the LPDDR2 interface at higher data rates, which LPDDR2 memory can’t attain without resorting to a very wide data bus and using several memory devices in the bargain. However the LPDDR2 parallel interface has a power advantage over the SPMT serial interface at lower transfer rates. So LPDDR2 memory might suffice for today’s embedded and mobile applications and might also suffice for low-activity modes in future applications.

The graph below, supplied by SPMT, tells the story. The graph shows that at low data rates, LPDDR2 memory dissipates less power than SPMT memory—largely because of the DLL integrated into SPMT memory. (DLLs consume non-negligable amounts of power and although DDR2 and DDR3 memories incorporate DLLs, LPDDR2 memory does not.) So the SPMT Consortium has done something very smart and has developed an integrated mode-switching mechanism called SerialSwitch, which allows an SDRAM controller to programmably shift an SPMT memory between its LPDDR2 and SPMT serial interface modes using a control register built into the memory device.

 

 

 

Mobile phone vendors and other embedded/mobile system designers know that video will be heavily used in many future products and they also know that memory transfer-rate and bandwidth requirements will only go up as a result. SPMT’s SerialSwitch mechanism provides a way for one memory device to support both low- and high-bandwidth operating modes with an appropriate level of power consumption depending on a system’s instantaneous bandwidth requirements. By definition, all commercial SPMT memories will incorporate the SerialSwitch feature. The following figure shows how the SPMT SerialSwitch mechanism works.

 

 

During Tg, the figure shows SPMT memory operating as a x16 LPDDR2 memory. Note that the data lines (DQ/HS) employ full-voltage, single-ended signaling in this mode. During time Tg, the memory’s DLL is off, which saves power. At the beginning of time Th, the system determines that more bandwidth is or soon will be needed, so it directs the memory controller to send a command to the memory to spin up the DLL in preparation for switching to SPMT serial mode. That process takes 5 to 10 microseconds. During this time, the memory continues to operate as an LPDDR2 memory so the DLL spin-up time is hidden and doesn’t interfere with system operation but power consumption will rise. Once the SPMT memory’s DLL has spun up, at time Ti, the system’s memory controller commands the SPMT memory to switch to serial communications mode. This transition takes a maximum of 10 clock cycles. After that and during time Tj in the figure above, the memory operates in SPMT serial-communications mode. Note that the data lines have switched to LVDS signaling, as shown in the figure. LVDS signaling reduces the memory interface’s power consumption. At some later time depending on system requirements, the memory controller can power down the memory (shown as time Tk) or switch back to LPDDR2 mode (the period following the period that starts at time Tk in the above figure). Don’t be misled by this figure by the way—SPMT memory need not pass through the power-down mode to switch from SMPT-serial communications to LPDDR2 mode.

Systems can use SPMT memory in LPDDR2 mode at boot time and whenever the system is operating in a mode with low memory-bandwidth requirements. The system can quickly switch to the LVDS SPMT-serial mode whenever it requires higher memory data rates—for example when video is activated, when multiple operating modes are in use simultaneously, or when multiple processors are running in a multicore device. The SPMT Consortium estimates that the optimum crossover point between LPDDR2 and SPMT serial interface data rates for a x16/8-lane LPDDR2/SPMT-serial memory device is around 1.6 Gbytes/sec based on energy considerations.

By subsuming the LPDDR2 standard and making SPMT memories wholly superset compatible with LPDDR2 memories, I think the SPMT consortium has significantly raised the likelihood of adoption when commercial SPMT memories finally appear late next year. I also think the likelihood of such memories appearing is pretty high considering that the top two DRAM vendors, Samsung and Hynix, are members of the SPMT Consortium. Together, Samsung and Hynix have a bit more than half of the overall DRAM market according to the latest stats from the DRAMeXchange (http://j.mp/aNaNiY).

On the embedded processor side of the equation, Marvel has announced that it too has joined the consortium, which further improves SPMT’s chances of success. In fact, Marvell supplied a canned quote for the SPMT Consortium’s press release with one of the strongest statements I’ve seen in such press releases, so I am suspending my usual cynicism about such quotes and reproduce it here:

“Today’s mobile DRAM technology is geared to support the bandwidth needs of single core processors. As devices evolve to integrate multi-core CPU, multi shader 3D graphic engines at multi-GigaHertz speeds, it’s clear that DRAM will be the single performance bottleneck, especially for handheld systems where power budget is a major constraint,” said Dr. Sehat Sutardja, chairman, president and chief executive officer at Marvell. “Marvell is joining the SPMT Consortium to actively promote Serial Port Memory Technology as an industry standard and address the immediate needs of the industry. We encourage other companies active in the sector to join us in our mission.”

Strong backing like this from a market maker like Marvell can only help SPMT’s cause. Whether or not SPMT actually reaches critical mass is something that we’ll all be watching as events unfold in the hotly competitive memory arena over the next 18 to 24 months.

State-of-the-Art in Low-Power Memory: Denali’s MemCon

June 30, 2009 on 4:06 pm | In DRAM, Flash, LPDDR, LPDDR2, Low-Power, SDRAM | No Comments

Need gobs of cheap RAM? Need it to operate at the lowest possible power? This blog’s for you.

I attended Denali’s ninth annual MemCon conference a few days ago. It was three days of intensive discussion about the state of the art in DRAM and Flash memory-the two mainstay memory technologies in use today. Surprisingly, NAND Flash memory is now the low-cost leader in terms of cost per bit, having passed by DRAM a few years ago. However, DRAM remains the mainstay memory for the vast number of designs and DDR SDRAM now rules as it becomes easier and easier to find microcontrollers and FPGAs with direct DDR interfaces and DDR controller and PHY IP for SOCs.

Memory power consumption as a percentage of system power consumption has grown with the rapid growth of memory-array size in all sorts of systems. A real eye opener at MemCon 09 was a chart on the power consumption of memory in server systems, where the large server memory arrays consume as much as 40% of the system power and the processor now consumes a mere 28%. Why is that important? It’s important because big server users like Google pay tens of millions of dollars each year in electrical power costs to run and to cool their server farms and 40% of a few tens of millions of dollars is, well, tens of millions of dollars.

Note that the current share-of-power percentages for servers don’t make processor power consumption unimportant-28% is still a big number-but the clear message is that server designers must now be far more concerned with memory power consumption because it’s a big part of the power puzzle. As embedded designs adopt large DDR memory DIMMs for bulk memory, the same sort of situation applies. Embedded designers must also be aware of the way their DRAM choices affect system power.

Marc Greenberg, Denali’s Director of Technical Marketing, gave a 2-hour tutorial on low-power DDR SDRAM on the first day of MemCon09. He threw up one slide that does a terrific job of putting all of the low-power SDRAM parts in perspective:

This slide shows the optimum type of SDRAM to use based on your design’s memory-capacity and speed requirements. I like this slide a lot because it helps you to pick from the wide array of DDR types and speeds. However, it seems that your selection job is about to become a lot simpler. Look what happens to the chart when you add in LPDDR2 memory:

LPDDR2 memory delivers the low-power goods by operating the SDRAM’s memory core and I/O at 1.2V, which is what you need to do to substantially cut memory power these days. Several manufacturers have announced LPDDR parts with I/O speeds to 400MHz/DDR800 and spec sheets for these parts are beginning to appear on DRAM vendor Web sites. LPDDR2 vendors with announced parts include Elpida, Hynix, Micron, and Nanya. Note that there’s also the possibility for existing LPDDR1 vendors to create parts that operate at 1.2V for similar power savings and that some of the soon-to-be-seen DDR3 parts may operate at 1.35V, which qualify them as low-power DRAMS.

In addition, there’s a spec for LPDDR2 non-volatile memory (LPDDR2-NVM) to allow LPDDR2 DRAM and Flash to be intermixed. The big advantage of Flash LPDDR2 is the very low standby power but Flash memory exhibits both read and write wear-out failure, so DRAM isn’t yet obsolete and you’ll likely need both memory types in your system design. The LPDDR2-NVM spec allows for I/O speeds to 533MHz/DDR1066 operation, but Greenberg says that the initial LPDDR2-NVM parts are likely to be slower than the maximum.